Book A Free Estimate

This post below on the subject of How to Install a Bathtub is without a doubt captivating. Check it out for your own benefit and see what you think about it.

Setting up a bath tub isn't specifically brain surgery, but it does need strong plumbing, woodworking, as well as occasionally, tiling abilities. Changing an old bath tub with a brand-new one is likewise a reasonably difficult task. If the old bathtub is conveniently obtainable, the job can move rapidly; if you have to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old bathtub and also embeded in the new one. Ensure you have certified on your own for the task as well as are comfortable attempting it. As opposed to working with a professional to take over a halfway-completed project, it is far better to think about employing one prior to you start. Possibilities are you may require a specialist plumber to make tube links.
This short article will certainly help you mount a brand-new bathtub in your bathroom if you have actually already bought a brand-new bathtub as well as don't require to alter the arrangement of your previous water pipelines.
Your tools and also product checklist should consist of the following:

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Blade


• Screwdriver


• Cold Chisel


• Measuring tape


• Pipe Caps


 

Preparing for the Installment

Firstly, the sustaining framework provided with the bath should be fitted (if called for) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is additionally practical to fit a supporting plate under the faucets unit to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps utilizing 2 nuts and olives (often supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet via the hole in the bath. Make use of the nut supplied by the maker to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its last placement.

Removing Old Taps

If you need to change old faucets with new ones as a part of your setup, after that the first thing you ought to do is disconnect the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of removing the existing faucets can be rather problematic as a result of the restricted access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that attaches the supply pipelines to the taps. Have a fabric all set for the remaining water that will originate from the pipelines. Once the supply pipes have actually been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from turning during this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Prior to going on to fit the new faucets, contrast the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.

Setting up the Tub

Utilizing both wood boards under its feet, put the tub in the needed setting. The wood boards are practical in uniformly spreading out the weight of the bathtub over the area of the boards instead of concentrating all the weight onto four small factors.
The following objective is to make certain that the bath tub is leveled all round. This can be attained by inspecting the level as well as changing the feet on the bathtub until the level reviews degree.
To set up faucets, fit the bottom of the furthest flexible faucet adapter to the ideal supply pipeline by making a compression join; then do the same for the various other tap.
Activate the water as well as check all joints and also brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow outlet and also the typical outlet for leaks.
Finally, fix the bathroom paneling as explained in the producer's instruction manual. Tiling and also securing around the tub needs to wait until the bath tub has actually been utilized at least when as this will certainly settle it right into its last setting.

Fitting New Touches

If the tails of the new taps are plastic, after that you will require a plastic port to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipe of the monobloc to the typical 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin ensuring that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the maker offered backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former kind should be linked to the tap ends initially, tightening just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have been attached.

Tiling Around the Bathtub

In the area where the bathroom meets the floor tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can move sufficient to crack an inflexible seal, causing the water to pass through the wall in between the bath and also the tiling, leading to difficulties with dampness as well as feasible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components as well as installations. They are sold in tubes as well as cartridges, and also can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Bear in mind to always fill up the bath tub with water prior to sealing, to enable the motion experienced when the bathtub remains in use. The sealant can split relatively very early if you do not think about this movement prior to sealing.
Conversely, ceramic coving or quadrant tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are also easily offered on the marketplace. It is suggested to fit the floor tiles using water-resistant or waterproof adhesive as well as grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

 

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

 

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

 

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

 

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

 

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

 

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

 

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

 

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

 

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

As a keen reader on How to Install a Bathtub, I assumed sharing that information was smart. Enjoyed our write up? Please share it. Help another person find it. Thanks a lot for your time spent reading it.

Visit Page